Space Monkey Mafia

Space Monkey Mafia "Space Monkey Mafia: Fine Galactic Goods Without the Astronomical Price!"

My arm and fingers felt good enough to get these together tonight. I left the brims on to help with filling if needed.
07/25/2025

My arm and fingers felt good enough to get these together tonight. I left the brims on to help with filling if needed.

And complete! They line up nicely on the previously failed pieces, too.
07/19/2025

And complete! They line up nicely on the previously failed pieces, too.

About 5 hours to go! Time to break out the pen to weld the parts along with using acrylic cement.
07/19/2025

About 5 hours to go! Time to break out the pen to weld the parts along with using acrylic cement.

Just a few hours past 1/2 way and looking good!
07/18/2025

Just a few hours past 1/2 way and looking good!

I do enjoy a good run out sensor and print pause for new filament. 🙂
07/17/2025

I do enjoy a good run out sensor and print pause for new filament. 🙂

Back at it after mostly recovering arm & hand straining from some sheet rock work. The video is the start of the uppers ...
07/17/2025

Back at it after mostly recovering arm & hand straining from some sheet rock work. The video is the start of the uppers for the failed hips and shins for Kali's armor. The best plate pics show the difference between the old and new and how deteriorated the old one got.

Welllll....*sigh* The tape did wonders for the support but fragged the rest of the prints. 🙄 In other news, Kali's Queen...
06/04/2025

Welllll....*sigh* The tape did wonders for the support but fragged the rest of the prints. 🙄 In other news, Kali's Queen Twi'lek lekku jewelry is coming along beautifully! 😊

35% along. I'm hoping the tape will hold long enough for that support to attach. It managed to restart a couple of times...
06/04/2025

35% along. I'm hoping the tape will hold long enough for that support to attach. It managed to restart a couple of times but not stable enough to stick. 🤷🏽‍♂️

19% finished, just under 58 hours to go. The other set came apart during finishing, so let's have another go, shall we?
06/03/2025

19% finished, just under 58 hours to go. The other set came apart during finishing, so let's have another go, shall we?

Gotta love a runout sensor! Just over 5 hours left and I put in a new reel of filament, load the head, and away it goes....
06/03/2025

Gotta love a runout sensor! Just over 5 hours left and I put in a new reel of filament, load the head, and away it goes. 😁 We'll see it around midnight or so.

06/02/2025

Here we are, a bit over half way there. These are looking so much better than the last set! The running temp inside is just shy of 90°F with a head temp of 216°C.

Alrighty then! Back at it after getting this crazy tent to keep a standard temp around the printer. It seems 65-70° does...
06/02/2025

Alrighty then! Back at it after getting this crazy tent to keep a standard temp around the printer. It seems 65-70° doesn't work well for prints. When the bed is going, the internal temp stays a comfy 83° and the prints are coming out smoother.
I'm now reprinting Kali's breast plate. The one I've been working on from the CR-10s has been separating and warping. It's time to give that one up as a learning experience and try with a better set up.

Address

624 San Francis Avenue
Stockton, CA
95210

Opening Hours

Monday 9am - 6pm
Tuesday 9am - 6pm
Wednesday 9am - 6pm
Thursday 9am - 6pm
Friday 9am - 6pm

Website

Alerts

Be the first to know and let us send you an email when Space Monkey Mafia posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Space Monkey Mafia:

Shortcuts

Share

Category